This is the latest recevied telemetry packets stored in our database for station/object XQ3PCN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1795126325 | 53 Count | 584 Count | 0 Count | 0 VDC | 0 VDC |
| 1795125421 | 52 Count | 559 Count | 0 Count | 0 VDC | 0 VDC |
| 1795124517 | 44 Count | 523 Count | 0 Count | 0 VDC | 0 VDC |
| 1795123613 | 43 Count | 496 Count | 0 Count | 0 VDC | 0 VDC |
| 1795122710 | 42 Count | 474 Count | 0 Count | 0 VDC | 0 VDC |
| 1795121806 | 41 Count | 450 Count | 0 Count | 0 VDC | 0 VDC |
| 1795120902 | 34 Count | 410 Count | 0 Count | 0 VDC | 0 VDC |
| 1795119998 | 33 Count | 388 Count | 0 Count | 0 VDC | 0 VDC |
| 1795119094 | 32 Count | 356 Count | 0 Count | 0 VDC | 0 VDC |
| 1795118190 | 31 Count | 331 Count | 0 Count | 0 VDC | 0 VDC |
| 1795117286 | 24 Count | 303 Count | 0 Count | 0 VDC | 0 VDC |
| 1795116383 | 23 Count | 274 Count | 0 Count | 0 VDC | 0 VDC |
| 1795115479 | 22 Count | 229 Count | 0 Count | 0 VDC | 0 VDC |
| 1795114575 | 21 Count | 202 Count | 0 Count | 0 VDC | 0 VDC |
| 1795113671 | 13 Count | 175 Count | 0 Count | 0 VDC | 0 VDC |
| 1795112768 | 12 Count | 145 Count | 0 Count | 0 VDC | 0 VDC |
| 1795111864 | 11 Count | 119 Count | 0 Count | 0 VDC | 0 VDC |
| 1795110960 | 10 Count | 89 Count | 0 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)