This is the latest recevied telemetry packets stored in our database for station/object DG0MG-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Temp* | Ubat* | TxPwr* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1795120072 | 8.7 degC | 3.62 V | 13 dBm | 0 | 0 |
| 1795119770 | 8.7 degC | 3.62 V | 20 dBm | 0 | 0 |
| 1795119469 | 8.7 degC | 3.62 V | 14 dBm | 0 | 0 |
| 1795119167 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795118865 | 8.7 degC | 3.63 V | 15 dBm | 0 | 0 |
| 1795118563 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795118261 | 8.7 degC | 3.63 V | 16 dBm | 0 | 0 |
| 1795117959 | 8.7 degC | 3.62 V | 20 dBm | 0 | 0 |
| 1795117658 | 8.7 degC | 3.63 V | 17 dBm | 0 | 0 |
| 1795117356 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795117051 | 8.7 degC | 3.62 V | 18 dBm | 0 | 0 |
| 1795116750 | 8.7 degC | 3.62 V | 20 dBm | 0 | 0 |
| 1795116448 | 8.7 degC | 3.63 V | 19 dBm | 0 | 0 |
| 1795116146 | 8.5 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795115542 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795114937 | 8.5 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795114333 | 8.5 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795113730 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
| 1795113126 | 8.7 degC | 3.63 V | 20 dBm | 0 | 0 |
*Used Equation Coefficients:
Temp: 0, 0.1, -273
Ubat: 0, 0.001, 0
TxPwr: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)